Customer Service: (323) 231-3525

Focal FDP1.900V2 Monoblock 850W RMS 2-Ohm Amplifier

  • SKU #: 04315
  • NewNew

Special Price $899.99

Retail: $1,099.99

($200.00 savings)

Availability: In Stock

Condition: Brand New
Shipping: Free Shipping
Sold As: Individually

* Required Fields

Special Price $899.99

Retail: $1,099.99

Focal FDP1.900V2 Monoblock 850W RMS 2-Ohm Amplifier

Click to view larger image

About the Focal FDP 1.900V2

High power for your subwoofer system

Focal's FDP 1.900V2 mono subwoofer amplifier can deliver up to 850 watts RMS to your subwoofer — providing the low-frequency foundation you need for your vehicle's high-powered audio system. The amp's Class D technology delivers this big-league power from a chassis that's smaller than a 2" stack of printer paper.

The extensive and versatile filter section lets you optimize the tone and performance for a wide variety of subwoofers, while a variable bass boost and adjustable phase focus the bass in your vehicle. The speaker-level inputs and auto turn-on let you connect this amp to almost any car stereo, even a factory radio.

Remote control and clip light

Focal includes a wired remote bass level controller so you can tweak your bass from song to song from your front seat. This remote also features an LED clip light that'll let you know if you're overloading the amp.

Focal FDP 1.900V2

 

Product highlights:

  • mono subwoofer amplifierClass D amp technology
    • 550 watts RMS x 1 at 4 ohms
    • 850 watts RMS x 1 at 2 ohms
    • 500 watts RMS x 1 at 1 ohm
  • variable low-pass filter (40-350 Hz, 24 dB/octave)
  • variable high-pass/subsonic filter (10-400 Hz, 24 dB/octave)
  • variable bass boost (0-6 dB at 40 Hz)
  • variable phase control (0-180 degrees)
  • red LED clip distortion light
More info:
  • wired remote level control with LED clip light included
  • bridgeable with a second FDP 1.900V2 amp to produce up to 1,700 watts RMS x 1 at 4 ohms
  • preamp inputs and outputs
  • speaker-level inputs (require speaker wire to RCA adapters)fuse rating: 25A x 2
    • auto signal-detection turn-on with high-level input
  • wiring and hardware not included with amplifierdimensions: 10.02"W x 2"H x 8"DMFR # FDP1.900V2
    • 8-gauge power and ground leads recommended

What's in the box:

  • Mono amplifier
  • Two 25-amp ATO fuses (internally installed)
  • 1 Long mounting bracket
  • 2 Short mounting brackets
  • Wired remote control
  • 16.5' Remote cable (RJ-25 plugs on each end)
  • 2mm Allen wrench
  • 3mm Allen wrench
  • 4mm Allen wrench
  • 4 Countersunk M4 x 8mm screws
  • Four 3/4" Screws
  • Two 3/8" Screws
  • 4 Rubber flat washers
  • Operations manual

 

Features & specs

Performance
RMS Power Output (Watts x Channels) 500 x 1
Peak Power Output (Watts x Channels) ---
Power at 2 Ohms (Watts x Channels) 850 x 1
Power at 1 Ohm (Watts x Channels) 500 x 1
Bridged Power (Watts x Channels) N/A
Minimum Impedance Bridged ---
Minimum Impedance Unbridged 1
Minimum Impedance 1
Best Frequency Response 10-350Hz Hz
THD at Rated RMS Power 1%
Signal to Noise Ratio 90 dB
Input Voltage 14.4v
Features
Amplifier Class D
Low-Pass Crossover Frequency 40-350 Hz
Low-Pass Slope (dB/octave) 24 dB/octave
High-Pass Crossover Frequency 10-48 Hz
High-Pass Slope (dB/octave) 24 dB/octave
Bass Boost 0-6 dB
Bass Boost Frequency 40 Hz
Fan Cooled No
Fuse Rating 50
Speaker Level Inputs Yes
Preamp Outputs 2
Width (inches) 10-1/16
Height (inches) 2
Depth (inches) 8

Additional Information