JL Audio Fix86 OEM Integration Digital Signal Processor with Automatic Time Correction and Digital EQ
- SKU #: 03012
Overview:
OEM Integration DSP with Automatic Time Correction and Digital EQ. 8-ch. Inputs / 4-ch. Stereo + 2 Subwoofer RCA Outputs
The FiX™ 86 is a state-of-the-art digital signal processor engineered to deliver outstanding sound from factory source units, while retaining OEM fader control.
Unlike typical OEM interface products, the FiX™ 86 automatically corrects time-delayed factory outputs prior to signal summing and EQ correction. Calibration takes just a single button press and about 30 seconds to complete, with no special equipment needed.
With a powerful 24-bit DSP processor and quad 1/3 octave equalizers onboard, complex factory signals, up to 3-way front and 2-way rear, are combined and level matched automatically into six, full-range stereo signals: Front (fader-controlled), Rear (fader-controlled) and Subwoofer (non-fading, front+rear summed) outputs.
By connecting a PC running TüN™ Software via USB, you can also access a complete suite of diagnostic panels that show the frequency response of input signals, as well as the corrected outputs. Adjustments can be made to input polarity, muting, and filtering, and new calibrations can be initiated from the PC as well. By clicking on the “TUNE” tab of the TüN™ interface, you can also access four, user-adjustable, 10-band, graphic equalizers to fine tune the output signals.
Differential-balanced inputs accept virtually any OEM analog audio signal, from low-voltage, line-level to high-power, amplified speaker-level outputs (up to 30V RMS).
Activation methods include 12-volt or Auto Turn-On (Signal/DC-Offset Sensing) to trigger a dedicated remote turn-on output for aftermarket equipment.
An optional DRC-100 or DRC-200 Digital Remote Controller (sold separately) adds Master Volume Control and/or Subwoofer Level Control from the driver’s seat.
Achieving great sound from your factory stereo has never been easier, or sounded better... Now with fader retention and subwoofer output!
Features & Specifications:
OEM Integration DSP with Automatic Time Correction and Digital EQ
• 8 Channel inputs
• 2 Channel Stereo RCA outputs
• 24-bit DSP processor
• Dual 1/3 octave equalizers
• Dimensions: 4.29"W x 6.14"D x 1.85"H
Power Supply Type | Regulated DC-DC SMPS |
Input Operating Voltage | 10 - 16 VDC |
Standby Current Draw | <1.5 mA |
Operating Current Draw | 0.7 A |
Recommended Fuse Value | 1 A |
Input Channels | Eight |
Input Type | Differential-Balanced |
Input Voltage Range | 250 mV - 30 V RMS |
Minimum Input Voltage | 10 mV RMS |
Input Level Setting | Fully automatic |
Output Channels | Six (Front/Rear/Sub Output Pairs) |
Analog Output | Unbalanced, stereo RCA jacks |
Digital Output | N/A |
Output Impedance | 450 Ω |
S/N Ratio | 96 dB (A-Weighted, referred to 4V RMS Output) |
THD+N @ Rated Output | 0.02% (20 Hz - 20 kHz) |
Audio Resolution | 24 bit / 48 kHz |
Number of EQ Bands | 30 x 2 channels |
EQ Resolution | 1/3 octave (25 Hz - 20 kHz) |
Remote Level Control | Optional (DRC-100 or DRC-200) |
Remote Level Functions | Master Volume Control, Handsfree Optimization, LED Status Reporting (DRC-200 adds Subwoofer Level Control) |
Specifications:
JLid™
Summary:
JLid™ is JL Audio's protocol for digital controllers and for communication of settings between devices (not for audio signals).
Detailed Information:
JLid™ offers two-way communication for a range of accessories, including the following:
Wired System Controllers: DRC-100, DRC-200, DRC-205
Bluetooth® Communicator: VXi-BTC
Networking Accessory: VXi-HUB
JL Audio FiX™ and TwK™ processors each feature one “JLid™ Port”, designed for connection of a wired controller.
JL Audio VXi amplifiers offer powerful networking capabilities via JLid™, to deliver single-point control of multiple amplifiers in a system. This allows the user to adjust levels (Volume, Fader, Balance, Zone Level) and to select from multiple DSP presets, across an entire group of networked amplifiers. JL Audio VXi amplifiers each feature separate “JLid™ Control” and “JLid™ Comm” ports. Please refer to the VXi product manual and our Help Center for details.
JLid™ connections are made via standard CAT-5e cables.
Additional Information
-
Focal ENFI1022 Home Audio 3-Way Crossover Made In France
Special Price $79.99
Retail: $199.99
-
Wet Sounds SW-808-W 8" 125 Watts RMS Marine Convertible Coaxial Speakers (White)
Special Price $399.99
Retail: $499.99
-
Special Price $1,949.99
Retail: $2,699.99
-
MOTO 600.4 - Arc Audio 4-Channel 600W RMS Ultra Compact Class D Amplifier
Special Price $649.99
Retail: $689.99
-
Alpine S-W12D4 12" 600W RMS Dual 4-Ohm S-Series Series Subwoofer
Special Price $199.99
Retail: $249.99